Accessories
CV300.
The Backbox CV300 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission.
APUi30C.
All new slim-line design, the single channel protection unit gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack. Please note that Edge speakers require the ‘C’ variant single channel protection unit.
APU-RS8iC/APU-RS16iC.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Edge Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation. Please note that Edge speakers require the ‘C’ variant of protection unit.
Firehood300.
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.
For use when there is insufficient cavity space for an Amina cavity backbox (less than 75mm). Allows installation of Amina loudspeakers into plasterboard with a rear cavity depth of just 30mm (rear of loudspeaker should be covered using soft insulation material where mounting blocks are used to prevent ingress of debris over time.
Shims are available to allow alignment of speaker and backbox with any thickness plasterboard other than 12.5mm (1/2”) (or multi-layered build-up), ensuring that no more than 2mm plaster is applied to the front of a plaster-over loudspeaker.
Shims can be used for alignment in a retrofit installation or alignment of Edgei series loudspeakers.
EDGE5i
CV345
The Backbox CV345 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission.
APUi50C.
The slim form of the APUi50C gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack.
APU-RS8iC/APU-RS16iC.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Edge Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation.
Firehood345.
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.
EDGE7i
CV345.
The Backbox CV345 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission.
APUi70C.
All new slim-line design, the single channel protection unit gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack. Please note that Edge speakers require the ‘C’ variant single channel protection unit.
Firehood345
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
APU-RS8iC/APU-RS16iC.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Edge Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation. Please note that Edge speakers require the ‘C’ variant of protection unit.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.
MOBIUS3i
CV300.
The Backbox CV300 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission where Mobius loudspeakers are installed into stud walls/ceiling.
SW300.
The BackboxSW300 provides a strong mechanical fixing method for solid blockwork and concrete walls/ceilings.
APUi30.
The slim form of the APUi30 gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack.
APU-RS8i/APU-RS16i.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Mobius Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation.
Firehood300
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.
MOBIUS5i
CV345.
The Backbox CV345 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission where Mobius loudspeakers are installed into stud walls/ceiling.
SW345.
The BackboxSW345 provides a strong mechanical fixing method for solid blockwork and concrete walls/ceilings.
APUi50.
All new slim-line design, the single channel protection unit gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack.
APU-RS8i/APU-RS16i.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Mobius Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation.
Firehood345.
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.
MOBIUS7i
CV345.
The Backbox CV345 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission where Mobius loudspeakers are installed into stud walls/ceiling.
SW345.
The BackboxSW345 provides a strong mechanical fixing method for solid blockwork and concrete walls/ceilings.
APUi70.
The slim form of the APUi70 gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack.
APU-RS8i/APU-RS16i.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Mobius Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation.
Firehood345.
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.
MOBIUS5i/S200
CV200.
The Backbox CV200 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission where Mobius loudspeakers are installed into stud walls/ceiling.
SW200.
The BackboxSW200 provides a strong mechanical fixing method for solid blockwork and concrete walls/ceilings.
APUi50.
All new slim-line design, the single channel protection unit gives reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack.
APU-RS8i/APU-RS16i.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Mobius Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation.
Firehood200.
When installing Amina Invisible Loudspeakers into a cavity wall or ceiling, it is the responsibility of the installer to ensure that the required fire rating of the wall/ceiling is maintained. By using Amina Firehoods by HoodyTM, you can easily meet these requirements with an inexpensive and easy to install solution, offering complete peace of mind.
Constructed from an intumescent kevlar material, the Firehood comes in three different sizes, meaning that there is an option for each of the three speaker sizes that Amina has to offer.
Design to provide a great solution for high end commercial installations, all Amina Invisible Loudspeakers can be supplied with high-quality toroidally wound transformers for both 100V and 70V line systems.
With a choice of either fixed-power or multi-tapped transformers available for all Amina Loudspeakers, the ability to specify a flexible and high performing invisible system has never been easier. Multi-tap transformer allows for adjustment to specification up to the moment of installation.